Waterproofing Engineering for Engineers, Architects, Builders, Roofers and Waterproofers |
Contents
| 195 | |
| 209 | |
| 217 | |
| 224 | |
| 231 | |
| 235 | |
| 238 | |
| 247 | |
| 48 | |
| 57 | |
| 63 | |
| 69 | |
| 75 | |
| 82 | |
| 89 | |
| 95 | |
| 101 | |
| 108 | |
| 114 | |
| 120 | |
| 126 | |
| 134 | |
| 140 | |
| 147 | |
| 153 | |
| 166 | |
| 176 | |
| 184 | |
| 189 | |
| 254 | |
| 260 | |
| 262 | |
| 273 | |
| 280 | |
| 293 | |
| 305 | |
| 313 | |
| 319 | |
| 331 | |
| 353 | |
| 360 | |
| 368 | |
| 379 | |
| 381 | |
| 388 | |
| 395 | |
| 403 | |
| 413 | |
| 423 | |
Other editions - View all
Common terms and phrases
aggregate applied asbestos asbestos shingles asphalt asphalt mastic Baumé binder bitumen brick brick-in-mastic burlap Catskill Aqueduct cement mortar cent coal-tar pitch consistency construction copper cotton fabric cracks cube-in-water method dampproofing distillation ductility engineer expansion joints Fahr feet flashing floor free carbon gilsonite grade gravel grout heated hydrated lime impervious iron joint filler kettles laid laps layer less linseed oil liquid masonry mastic melting melting-point membrane metal mixed mixture mopped mortar coat nails naphtha paraffin penetration petroleum petrolic ether pipe placed plies Portland cement pounds powdered practice proportions protected roof sand saturated and coated seams SECTION sheet shingles shown in Fig sieve soluble specific gravity Specifications for Waterproofing specimens steel stone strip structure Subway surface coating system of waterproofing tank temperature tiles treated felt trowel tunnel untreated usually walls waterproofing compounds waterproofing materials watertight weight
Popular passages
Page 149 - Natural cements are produced by burning a naturally impure limestone, containing from 15 to 40 per cent of silica, alumina, and iron oxide, at a comparatively low temperature, about that of ordinary lime burning. The operation can therefore be carried on in a kiln closely resembling an ordinary lime kiln.
Page 272 - The sample shall be a fair average of the shipment. Three per cent of the packages shall be sampled. The sample shall be taken from the surface to the center of the package. A 2-lb.
Page 217 - The upper surface of the cover should burn clear, but the under surface should remain covered with carbon. To find Volatile Combustible Matter, subtract the per cent.
Page 414 - Blown Petroleums. — Semi-solid or solid products produced primarily by the action of air upon liquid native bitumens which are heated during the blowing process.
Page 199 - Apply the heat in such a manner that the temperature of the water is raised 5° C.
Page 413 - The components of the bitumen in petroleums, petroleum products, malthas, asphalt cements and solid native bitumens, which are soluble in carbon disulphide but insoluble in carbon tetrachloride.
Page 413 - Solid or semi-solid native bitumens, solid or semisolid bitumens obtained by refining petroleum, or solid or semi-solid bitumens which are combinations of the bitumens mentioned with petroleums or derivatives thereof, which melt upon the application of heat and which consist of a mixture of hydrocarbons and their derivatives of complex structure, largely cyclic and bridge compounds.
Page 416 - Fixed Carbon. — The organic matter of the residual coke obtained upon burning hydrocarbon products in a covered vessel in the absence of free oxygen.
Page 199 - ... that the thermometer registers an increase of 5° C. per minute. The temperature at which the bitumen touches a piece of paper placed in the bottom of the beaker is taken as the melting point. Determinations made in the manner described should not vary more than 2° for different tests of the same material.
Page 195 - ... particles. Not more than one-half of the total amount of naphtha required should be used until the sample is entirely broken up. The balance of the 100 cc.